Article

The SMRP Metrics Every CMRP Candidate Must Know

· Monarch Reliability

The CMRP exam is closed book. If a question uses an SMRP Best Practices metric, you have to know the short-form equation and what every symbol means. Memorizing names is not enough. You need to be able to rebuild the formula and explain why a term is in the numerator or the denominator.

This article covers the metrics that do the most work in study and on practice exams. It is not a substitute for the full list. All 69 numbered metrics from the 7th edition, each with its equation, variable key, and edition notes, are on our SMRP formulas page. Wording below is our own. These are not official exam questions, and we are not affiliated with SMRP.

Where the 6th and 7th editions define something differently, or where the 7th edition does not speak with one voice, that is flagged.

Start with replacement asset value

Several Pillar 1 metrics are ratios of a cost or a headcount to replacement asset value (RAV). Use replacement value, never book value or insured value.

Maintenance cost as a percent of RAV (1.5)

  • Equation: (C_m / RAV) × 100
  • Key: C_m = total maintenance cost for the period; RAV = replacement asset value

If annual maintenance cost is $3.0 million and RAV is $100 million, the result is 3.0%. The same idea appears in stocked MRO as a percent of RAV (1.4) and in RAV per craft-wage employee (1.1).

RAV per craft-wage headcount (1.1)

  • Equation: RAV / n_c
  • Key: RAV = replacement asset value; n_c = craft-wage headcount in FTE, including contractors used to supplement routine work

These metrics were revised in the 7th edition. The idea did not change: the denominator is replacement value, and craft-wage headcount is a labor capacity figure, not a headcount of everyone in the department.

Availability is not uptime

This is one of the most common mix-ups in CMRP study.

Availability (2.2)

  • Equation: A = T_o / (T_a − T_i)
  • Key: T_o = uptime = T_a − (T_i + T_d); T_a = total available time; T_i = idle time; T_d = total downtime. Often written × 100 as a percent.

Uptime (2.3)

  • Equation: T_o = T_a − (T_i + T_d)
  • Key: uptime percent = T_o / T_a × 100. The denominator is total available time, including idle time — unlike availability.

Idle time is time the asset is not scheduled because nothing is required of it. It is not downtime. In the 7th edition, availability is net of idle time and is meant to be consistent with OEE and TEEP. If you forget that and put idle time in the availability denominator, you understate availability and you will not match OEE.

A quick check: T_a = 720 h, T_i = 240 h, T_d = 80 h. Then T_o = 400 h, availability is 400 / 480 = 83.3%, and uptime percent is 400 / 720 = 55.6%. Same hours, different denominators.

OEE and TEEP are related, not interchangeable

Overall equipment effectiveness, OEE (2.1.1)

  • Equation: OEE = A × P × Q
  • Key: A = availability (metric 2.2); P = r_a / r_best (actual rate / best rate), or if you have cycle times, P = t_best / t_actual; Q = good units / total units. This is the OEE 2 form: effectiveness while the asset is scheduled to operate.

Total effective equipment performance, TEEP (2.1.2)

  • Equation: TEEP = U × A × P × Q
  • Key: U = utilization time / total available time (metric 2.5); A, P, and Q are the same as in 2.1.1

OEE leaves idle time out, because availability is already net of idle time. TEEP puts utilization back in, so you see the all-hours picture. Do not call a TEEP figure an OEE figure.

Edition note on cycle time. When the data are cycle times, performance must fall when the actual cycle is longer than the best cycle. We use P = t_best / t_actual, which is also the form in Guideline 2.0 and in the note that performance cannot exceed 100%. The 2.1.1 formula box in the 7th edition prints actual ÷ best for cycle time, which inverts the ratio and would push P above 1 when the line is slower than standard. If a question quotes a formula, use the formula in the question. If it does not, use best over actual.

Both 2.1.1 and 2.1.2 were revised in the 7th edition.

The mean-time family

Learn these as a set, because the exam-style errors are almost always a wrong denominator or a mixed-up delay.

Mean time between failures, MTBF (3.5.1), for repairable items:

  • Equation: MTBF = T_o / n_f
  • Key: T_o = operating (uptime) hours in the period; n_f = number of failures in the period

Mean time to repair, MTTR (3.5.2):

  • Equation: MTTR = T_r / n_r
  • Key: follow the question. In this course we treat T_r as active repair time and n_r as the number of repairs.

Mean downtime, MDT (3.5.4):

  • Equation: MDT = T_d / n_d
  • Key: T_d = total downtime, including administrative and logistic delay, not only the wrenches-on period; n_d = number of downtime events

Edition note on MTTR. The 7th edition does not speak with one voice. Note 2 under metric 3.5.2 counts time from stop to restored, including administrative and logistic delay. Metric 3.5.4 and Guideline 6.0 treat MTTR as pure or active repair. We teach the second reading, and we keep delays in MDT, so the two measures stay distinct. On the exam, use the definition the question gives you.

MTTF is for items you replace rather than repair. Do not report MTTF as MTBF, or the other way around.

Several mean-time metrics are marked as revised in the 7th edition. The safe habit is the same in either edition: write the equation, name every variable, and check whether delay is in or out.

Work-management measures worth knowing cold

You will also want the work-flow metrics in your head, because they turn up in scenario items as well as in calculations.

Planned work (5.3.1) is planned hours over total maintenance hours, as a percent.

Reactive work (5.4.1) is reactive hours over total maintenance hours. It is not the same thing as unplanned work (5.3.2), which is work that never had a job plan. A job can be planned and still be reactive if it broke in.

Rework (4.1) uses rework hours over total maintenance labor hours. Use the official denominator, not a count of work orders, unless the question says otherwise.

Wrench time (5.6.1) is measured by work sampling: wrench-time observations over total observations, as a percent. Travel, waiting, permits, and instruction are not wrench time. A gut-feel estimate is not the metric.

Standing work orders (5.4.5) — hours on standing work orders over total maintenance labor hours — is new as a numbered metric in the 7th edition.

How to study them

Write a short list from memory twice a week: OEE, TEEP, availability, uptime, idle time, utilization, MTBF, MTTR, MDT, maintenance cost % RAV, planned work, reactive work, rework, and wrench time. For each one, write the equation and a one-line key. Then check yourself against the full formulas page.

When you practice, say the key out loud before you compute. The arithmetic is usually simple. The errors are almost always a wrong base: book value instead of RAV, uptime's denominator used for availability, OEE reported as TEEP, or delay folded into MTTR when the question wanted active repair.

If you want to test this with worked items, start with the free CMRP diagnostic or the sample CMRP questions. Full-length practice at the official 110-question, 2.5-hour length is in the $99 practice exam pack.

Independent exam prep. Not affiliated with SMRP.